The Manage Storage menu pane allows you to see the status and configuration of the Storage Pool and all disk volumes present within the system. From this menu pane, you can create or destroy the Storage Pool, replace failed disks and perform a rebuild of the Storage Pool, or add disks to the Storage Pool to expand storage capacity.
To access the Storage Pool:
- In the Appliance menu pane, click Manage Storage.
You will be able to see Storage Status information, Storage Pool information, and more.
- In the Storage Status section, review the current configuration and status of the Storage Pool. For example:
- The pool State field should be marked as Online.
- The State of each disk volume present should be marked as Online.
- The Read, Write, and CKSum error count columns should be marked as 0.
- The Errors field should be marked as No Known Errors.
Note: Contact eFolder Replibit Support if the Storage Status section does not display expected values.
Note: Use the Destroy Pool option with caution. Clicking Destroy Pool will delete the storage pool and all data. This is an irreversible action.
Storage Pool Operations
The Storage Pool menu allows you to view the current RAID level, Disk-Set size, and compression settings.
- Click to expand the Storage Pool menu.
- Review the current RAID level, Disk-Set size, and Compression settings.
For example, the example above lists RAID6 using 4 disks per RAID volume set, with a Compression scheme of LZ4.
Failed Disks (Identifying and Replacing)
In the event that disks within the Storage Pool have failed, the Storage Status will change from Online to Degraded or Faulted, depending on the severity of the failure and the RAID level selected.
In the event that sufficient RAID redundancy exists, the Storage Pool will become Degraded but will continue to operate in RAID Recovery mode. Performance will be impacted but the device will continue to function, and no customer data will be lost.
Failed disks should be replaced as soon as possible in order to restore RAID redundancy and prevent the possible loss of customer data should additional storage pool disks fail.
- When you have replaced the failed disks within the device, navigate to the Manage Storage menu and click to expand the Failed Disks section.
- Click the Replace button to start the failed disk recovery process.
The Replace Disk dialog box displays.
- In the Unused Disk dropdown menu, select an available disk that is as large as or larger than the original failed volume.
- Click the Replace button to begin rebuilding the RAID set onto the replacement drive.
If insufficient RAID redundancy exists to provide for the failed disk volumes, the Storage Pool will become Faulted and all customer data present will be lost. Faulted Storage Pools will have to be destroyed and then recreated again once the failed disks have been replaced. For instructions on retrieving data from the Vault, please reference the Recovering a Protected System from a Vault article.
Used Disks (Disk Device Identification)
The Used Disks section displays a list of all disk volumes in use, along with identifying information.
- Click to expand the Used Disk section.
- Use the columns to view information about disk volumes in use, including:
- Disk displays the local device address of the disk.
- Disk Type displays whether the device is a local physical volume or a remote iSCSI LUN.
- IQN lists the identity of attached iSCSI LUN’s.
- Disk ID displays the identity of the device within the Storage Pool.
- TargetIP and TargetPort displays connection information about the iSCSI Target.
- Disk Status shows the current status of the disk.
- Size displays the total size of the volume.
Unused Disks (Expanding the Storage Pool)
The Unused Disks section displays a list similar to the Used Disks display described above. Unused Disks may be used to expand the capacity of the Storage Pool.
To add additional storage capacity to the pool:
- Click to expand the Unused Disks section.
- Select the minimum number of disks. Minimum Disks is defined as the number of disks used to initially create the storage pool. In the image listed below, Minimum Disks is displayed in the RAID Level configuration, as well as noted under Compression Level.
- Use the checkboxes to select a set of disks that are the same size. The size does not have to be the same as other RAID sets already assigned to the Storage Pool.
- Click the Add to Storage button to create a new RAID set and add it to the existing Storage Pool.
Note: Additional RAID sets are Spanned onto the existing Storage Pool similar to RAID-0. For example, if your Storage Pool is configured for RAID-5, then adding a new RAID set is similar to RAID-50. Each RAID set contains its own set of redundant disks, so for example, a single disk could be lost from each RAID-5 set without losing data integrity of the Storage Pool.
iSCSI Storage (Managing Remote Storage Volumes)
eFolder Replibit supports using external iSCSI disk volumes for creating the Storage Pool.
iSCSI utilizes the network layer instead of a dedicated storage controller when performing disk and storage operations. Multiple network adapters should be employed when utilizing iSCSI for the Storage Pool in order to prevent network performance bottlenecks.
Important: We do not recommend mixing Local storage with iSCSI storage devices when creating the Storage Pool.
Note: iSCSI network traffic may be segregated from backup traffic by placing it in an alternate subnet bound to a second physical NIC. For more information, please reference the Managing Replibit Settings article.
Note: It is highly recommended to utilize 10Gbe Ethernet cards when using iSCSI devices for the Storage Pool to improve disk performance.
Important: Using 1Gbe Ethernet (even when using multi-path) for iSCSI Storage Pool devices is officially unsupported by the eFolder Replibit Support team, due to poor performance concerns. Use at your own risk.
- Click to expand the iSCSI Storage section.
This section displays iSCSI Initiator management settings.
- In the Server IP field, enter the iSCSI Target Server IP address.
- In the Port field, enter the port number if it has been changed from the default port.
- Click the Scan button to search for accessible storage volumes.
- Click Add on each discovered disk volume that you would like use as a Storage Pool disk for the appliance.